Running problems

Hi,
I'm having some running isusses, I have recently switched back to injection ( had fireblade carbs that was done by the last owner) but it's now idleing high and when you try to rev it the revs drop off? I still have a mk1 dizzy on it, will it solve it if I switch back?
The afm is back on along with most of the induction kit. It is also running abit rich still.

Does any one have any pics or diagrams of then engine I.e where the pipes and plugs go so I can double check as most of it was a combination of using pics off google an gess work lol.
Cheers.

download workshop manual dude

Not enough info.
Is your car mk1 or post mk2?
If your car is mk2 and after, it won't run as so many signal for ECU to work.

Cheers
Atchi

you need to put the mk2 dizzy on there


steve

Yh it's a mk 2. I will down load one. Which one the best manual? An I stick the mk2 dizzy on 2 day see what happens. Cheers all.

Hi,

Do you still have MAF and TPS?
How about fuel pressure?
Do you get check engine light comes on?

Good luck.

Cheers
Atchi

Yh afm an tps on. Engine check is still on tho :s gonna do the dizzyin a min
Cheers all

Now dizzy, tps,afm and lambda all on an to be hounest I'm not sure if it better or worse ? It's still not right. I might burn it! Any ideas would really help. I got a work shop manual on disc just need a computer now lol ( I on the site now with phone) I have a new fuel reg an it set too 2.7bar which according to the autodata at my work is about right ( it say 2.5 to 2.7 ) so the fuel side of things looks to be ok. As for the air the breather pipe from the rocker is not on the induction pipe as I don't have the right one for the car and the one off the intake is not connected ether but on other cars they don't seem to make tht much diff? please help
Cam

sounds like an air leak, what gasket is being used on the manifold to head junction? are all unused hose ends blocked

GTP

Hose ends r blocked an I'll check the inlet mani tht could well be it! Thanks i will jus get a new gasket a see what happens. Cheers
I let u know
Cam

mine wont run if you disconnect the hose from the air intake to the rail on top the intake manifold, could be your problem......

Ok thanks jus made up in intake pipe I'll try it 2moz night thanks for your help all. let u all know how it goes
Cam

what ecu are you using? you need standalone to run TBs dont you?

I only running standard again except cams now. Although I do fink that it does have stage 2 chip. But I dono.
Cam

is it still cutting out when you touch the throttle? i had a bad chip once which acted the same.

Well the it seemed to have went after I changed the s#*# fuel reg with a malpassi one but still wasn't good. Goin to try find time 2 night to fit up the new inlet gasket and induction pipe. I almost getting excited now hehe hopefully I can go play init soon then all I need is retrim an repaint. I was looking on another forum yesterday an someone had put some Whiteline rear toe arms from a scooby on they look s**thot. I might do it any idea how hard it would be. The only thing I noticed was the size of the bush , looked a lot fatter ? Cheers
Cam

youv got to mod the chassis end of the arms for the scooby mod
there are parts on ebay you can use to make up an adjust arm kit, cheaper and easyer than getting some made up

Cheers I have a look. See whats there

I think they are called turn buckles, m12 you want, I think the bloke selling them is called mcmillin motorsport, something like that
Plus you will need left and right handed rodends and lock nuts from the same place

Oh ok thanks. So far on the running side of things the inlet mani is back off and is being cleaned out 2day (not tht much to clean out of it but still good to check) an new gasket all the way round it. Got to get some pipeing and joins. Can anyone tell me where the water feed comes from to the isc? I know it from the head somewhere but most of the work I'm doin is in the dark with a crap lead lamp off a flat ka battery lol, so a general direction would be grate thanks

An thanks dominator I'll have a look at them.

Now there is a new gasket on every join on the inlet mani. An it won't start at all now. Was thinking my ecu could be at fault? anyway I could tell if it has been chipped ? I got the ecu out but to be honest I dono what I'm lookin at. :s. Please help